| 10:56:11.491 | Running procedure: 8.2.1.2.10 | |
| 10:56:11.493 | This procedure is enabled because the following options: | |
| 10:56:11.493 | - supports.binaryOutput.commands == true | |
| 10:56:11.493 | - supports.disable.binaryOutput == true | |
| 10:56:11.493 | step: 1 | |
| 10:56:11.493 | - The DUT's binary outputs can be uninstalled or disabled through its configuration | |
| 10:56:11.493 | step: 2 | |
| 10:56:11.493 | - Uninstall or disable every binary output point on the DUT | |
| 10:56:11.494 | [PLG] | All binary output status points were uninstalled |
| 10:56:11.494 | [PLG] | Cycling power |
| 10:56:11.495 | step: 3 | |
| 10:56:11.495 | - Select(0x03) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x00 | |
| 10:56:11.495 | - g12v1, 2-Byte Count and Index, count: 1 | |
| 10:56:11.495 | - [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:11.495 | --A-> | Select(0x03) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x00 |
| 10:56:11.495 | g12v1, 2-Byte Count and Index, count: 1 | |
| 10:56:11.495 | [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:11.495 | --T-> | fir: 1 fin: 1 seq: 0 |
| 10:56:11.495 | --L-> | master: 1 pri: 1 fcb: 0 fcv: 0 func: UNCONFIRMED_USER_DATA(0x04) 0xC4 length: 26 dest: 1024 src: 1 |
| 10:56:11.495 | --P-> | 05 64 1A C4 00 04 01 00 EC 47 |
| 10:56:11.495 | C0 C0 03 0C 01 28 01 00 00 00 03 01 64 00 00 00 FD 6B | |
| 10:56:11.495 | C8 00 00 00 00 78 FB | |
| 10:56:11.496 | step: 4 | |
| 10:56:11.496 | - Read a single fragment response w/ sequence(0x00) | |
| 10:56:11.496 | - Verify that the IIN field contains at least one of IIN(ParamError, ObjectUnknown) | |
| 10:56:11.497 | <-P-- | 05 64 1C 44 01 00 00 04 7F 9B |
| 10:56:11.497 | C0 C0 81 90 04 0C 01 28 01 00 00 00 03 01 64 00 1E 04 | |
| 10:56:11.497 | 00 00 C8 00 00 00 04 00 22 | |
| 10:56:11.497 | <-L-- | master: 0 pri: 1 fcb: 0 fcv: 0 func: UNCONFIRMED_USER_DATA(0x04) 0x44 length: 28 dest: 1 src: 1024 |
| 10:56:11.497 | <-T-- | fir: 1 fin: 1 seq: 0 |
| 10:56:11.498 | <-A-- | Response(0x81) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x00 IIN(DeviceRestart, NeedTime, ParamError) |
| 10:56:11.498 | g12v1, 2-Byte Count and Index, count: 1 | |
| 10:56:11.498 | [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 4 (NOT_SUPPORTED) | |
| 10:56:11.498 | step: 5 | |
| 10:56:11.498 | - Check that no binary control point operated | |
| 10:56:12.499 | [PLG] | Binary output did NOT operate |
| 10:56:12.499 | Passed procedure: 8.2.1.2.10 | |
| 10:56:12.499 | restore | |
| 10:56:12.499 | - Reinstall or re-enable the points that were uninstalled or disabled, so later procedures can use them | |
| 10:56:12.499 | [PLG] | All points were reinstalled |
| 10:56:12.499 | [PLG] | Cycling power |