| 10:56:13.221 | Running procedure: 8.2.1.2.13 | |
| 10:56:13.223 | This procedure is enabled because the following options: | |
| 10:56:13.223 | - supports.binaryOutput.commands == true | |
| 10:56:13.223 | step: 2 | |
| 10:56:13.223 | - Tell a manual tester: Watch binary output 0 during this procedure: it should operate once after the OPERATE in step 4, and not again after the repeated one in step 7. You'll be asked what you saw after the steps, so make sure you can tell one operation from two (e.g. a counter, or an on-time long enough to see). Get ready, then press ENTER. | |
| 10:56:13.223 | - Select(0x03) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x00 | |
| 10:56:13.223 | - g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.223 | - [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.223 | --A-> | Select(0x03) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x00 |
| 10:56:13.223 | g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.223 | [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.224 | --T-> | fir: 1 fin: 1 seq: 0 |
| 10:56:13.224 | --L-> | master: 1 pri: 1 fcb: 0 fcv: 0 func: UNCONFIRMED_USER_DATA(0x04) 0xC4 length: 24 dest: 1024 src: 1 |
| 10:56:13.224 | --P-> | 05 64 18 C4 00 04 01 00 5B 61 |
| 10:56:13.224 | C0 C0 03 0C 01 17 01 00 03 01 64 00 00 00 C8 00 FD 11 | |
| 10:56:13.224 | 00 00 00 FF FF | |
| 10:56:13.224 | step: 3 | |
| 10:56:13.224 | - Read a single fragment response w/ sequence(0x00) | |
| 10:56:13.224 | - Verify the response contains the exact object header: | |
| 10:56:13.224 | - g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.224 | - [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.224 | - Verify that the IIN field does not contain bits IIN(ParamError, ObjectUnknown, FuncNotSupported) | |
| 10:56:13.225 | <-P-- | 05 64 1A 44 01 00 00 04 A6 F0 |
| 10:56:13.225 | C0 C0 81 90 00 0C 01 17 01 00 03 01 64 00 00 00 9C 9A | |
| 10:56:13.225 | C8 00 00 00 00 78 FB | |
| 10:56:13.225 | <-L-- | master: 0 pri: 1 fcb: 0 fcv: 0 func: UNCONFIRMED_USER_DATA(0x04) 0x44 length: 26 dest: 1 src: 1024 |
| 10:56:13.225 | <-T-- | fir: 1 fin: 1 seq: 0 |
| 10:56:13.225 | <-A-- | Response(0x81) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x00 IIN(DeviceRestart, NeedTime) |
| 10:56:13.225 | g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.225 | [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.225 | step: 4 | |
| 10:56:13.225 | - Operate(0x04) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x01 | |
| 10:56:13.225 | - g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.225 | - [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.225 | --A-> | Operate(0x04) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x01 |
| 10:56:13.225 | g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.225 | [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.225 | --T-> | fir: 1 fin: 1 seq: 0 |
| 10:56:13.225 | --L-> | master: 1 pri: 1 fcb: 0 fcv: 0 func: UNCONFIRMED_USER_DATA(0x04) 0xC4 length: 24 dest: 1024 src: 1 |
| 10:56:13.225 | --P-> | 05 64 18 C4 00 04 01 00 5B 61 |
| 10:56:13.225 | C0 C1 04 0C 01 17 01 00 03 01 64 00 00 00 C8 00 35 C7 | |
| 10:56:13.225 | 00 00 00 FF FF | |
| 10:56:13.225 | step: 5 | |
| 10:56:13.225 | - Read a single fragment response w/ sequence(0x01) | |
| 10:56:13.225 | - Verify the response contains the exact object header: | |
| 10:56:13.225 | - g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.225 | - [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.225 | - Verify that the IIN field does not contain bits IIN(ParamError, ObjectUnknown, FuncNotSupported) | |
| 10:56:13.226 | <-P-- | 05 64 1A 44 01 00 00 04 A6 F0 |
| 10:56:13.226 | C1 C1 81 90 00 0C 01 17 01 00 03 01 64 00 00 00 08 B9 | |
| 10:56:13.226 | C8 00 00 00 00 78 FB | |
| 10:56:13.226 | <-L-- | master: 0 pri: 1 fcb: 0 fcv: 0 func: UNCONFIRMED_USER_DATA(0x04) 0x44 length: 26 dest: 1 src: 1024 |
| 10:56:13.226 | <-T-- | fir: 1 fin: 1 seq: 1 |
| 10:56:13.226 | <-A-- | Response(0x81) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x01 IIN(DeviceRestart, NeedTime) |
| 10:56:13.226 | g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.226 | [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.226 | step: 6 | |
| 10:56:13.226 | - Check that binary control point 0 operate | |
| 10:56:13.226 | [PLG] | Binary output 0 did operate |
| 10:56:13.226 | step: 7 | |
| 10:56:13.226 | - Operate(0x04) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x01 | |
| 10:56:13.226 | - g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.226 | - [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.226 | --A-> | Operate(0x04) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x01 |
| 10:56:13.226 | g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.226 | [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.226 | --T-> | fir: 1 fin: 1 seq: 0 |
| 10:56:13.226 | --L-> | master: 1 pri: 1 fcb: 0 fcv: 0 func: UNCONFIRMED_USER_DATA(0x04) 0xC4 length: 24 dest: 1024 src: 1 |
| 10:56:13.226 | --P-> | 05 64 18 C4 00 04 01 00 5B 61 |
| 10:56:13.226 | C0 C1 04 0C 01 17 01 00 03 01 64 00 00 00 C8 00 35 C7 | |
| 10:56:13.226 | 00 00 00 FF FF | |
| 10:56:13.226 | step: 8 | |
| 10:56:13.226 | - Read a single fragment response w/ sequence(0x01) | |
| 10:56:13.226 | - Verify the response contains the exact object header: | |
| 10:56:13.226 | - g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.226 | - [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.226 | - Verify that the IIN field does not contain bits IIN(ParamError, ObjectUnknown, FuncNotSupported) | |
| 10:56:13.227 | <-P-- | 05 64 1A 44 01 00 00 04 A6 F0 |
| 10:56:13.227 | C2 C1 81 90 00 0C 01 17 01 00 03 01 64 00 00 00 9C 6F | |
| 10:56:13.227 | C8 00 00 00 00 78 FB | |
| 10:56:13.227 | <-L-- | master: 0 pri: 1 fcb: 0 fcv: 0 func: UNCONFIRMED_USER_DATA(0x04) 0x44 length: 26 dest: 1 src: 1024 |
| 10:56:13.227 | <-T-- | fir: 1 fin: 1 seq: 2 |
| 10:56:13.227 | <-A-- | Response(0x81) fir: 1 fin: 1 con: 0 uns: 0 seq: 0x01 IIN(DeviceRestart, NeedTime) |
| 10:56:13.227 | g12v1, 1-Byte Count and Index, count: 1 | |
| 10:56:13.227 | [0] - code: 0x03 (LATCH_ON, NUL) count: 1 onTime: 100 offTime: 200 status: 0 (SUCCESS) | |
| 10:56:13.227 | step: 9 | |
| 10:56:13.227 | - Check that no binary control point operated | |
| 10:56:14.228 | [PLG] | Binary output did NOT operate |
| 10:56:14.228 | Passed procedure: 8.2.1.2.13 |